LOW CURRENT
SOLID STATE RELAY

Type : SSR-WG4-200V-xxxVyy-1A

Where:
xxx=Maximum Switched Voltage
yy=AC or DC

Description:
The SSR-WG4-200V-xxxVyy-1A is a solid state relay designed to accept a wide input voltage range of 4-200 volts peak to control a DC or AC voltage, depending upon the model selected, not greater than 200 Volts at 1 Amp. This makes it ideal for direct connection to unbuffered microprocessor port pins or other applications that are incapable of driving standard loads such as relays. The relay provides for very high speed on/off switching times allowing the control voltage to operate from DC to 3 KHz maximum. The input control voltage is magnetically coupled to the output switch to provide maximum isolation. The relay has no moving parts thereby eliminating the bounce and burning of contacts normally associated with mechanical relays. This relay is a single-pole, normally open (Form 1A) solid state replacement for low current electromechanical relays.

Application:
The solid state relay provides complete isolation between the input and output terminals. The input can be driven by an AC or DC voltage from 4 to 200 Volts Peak. The drive current required is 1mA minimum. This makes the solid state relay an ideal control module for low power devices. A typical application would be an AC or DC load which requires a microprocessor to control the on and off states. Another application involves using the solid state relay to interface between a TTL or CMOS output, such as a rotary encoder or counter, and a data line going through a noisy environment.

Technical Specifications:
All specifications typical at nominal line, full load and 25°C unless otherwise specified.

General Specifications:

Minimum Typical Maximum
Switch-On Time n/a 20 uSec n/a
Switch-Off Time n/a 20 uSec n/a
Isolation Voltage n/a n/a 2500 Volts
Isolation Resistance 10,000 n/a n/a
Isolation Capacitance n/a n/a 10 pf

Input Specifications:

Minimum Typical Maximum
Input Control Voltage Range 4 Volts Peak n/a 200 Volts Peak
Input Control Current Range 1 mA n/a 2.5mA
Input Frequency DC n/a 3 KHz

Output Specifications:

Output Voltage Range
SSR-WG4-200V-200VDC-1A 0 VDC n/a 200 VDC
SSR-WG4-200V-120VAC-1A 0 VDC n/a 120 VAC RMS*
Output Current Continuous n/a n/a 1.0 Amps**
Output Power n/a n/a n/a
SSR-WG4-200V-200VDC-1A n/a n/a 200 Watts
SSR-WG4-200V-120VAC-1A n/a n/a 120 Watts
On-State Resistance @ 48 VDC n/a n/a n/a
SSR-WG4-200V-200VDC-1A n/a n/a 0.18 Ohms
SSR-WG4-200V-120VAC-1A n/a n/a 0.18 Ohms
Off-State Resistance n/a n/a > 1 MOhm
Output Capacitance n/a 200 pF n/a


* Other voltages are available. Contact us for specifications.
** Operation at higher amperages is possible but depends on duty cycle and switch on/off times. Contact us for specifications.

Packaging:
Type: WEG 4 terminal modular housing, #12 to #22 AWG terminals
Size: 60.6mm x 90.5mm x 22.5mm (2.39" x 3.56" x 0.89") (W x H x D excluding DIN rail)
Operating Conditions:
-40 to +85°C, 0 to 93% Relative Humidity
Ordering Part Number:
SSR-WG4-200V-200VDC-1A
SSR-WG4-200V-120VAC-1A

Specifications are subject to change without notice.

Miscellaneous Controllers

Websites to visit!

HydraForce Inc.
Advanced Surge Suppressors
Mobile Electronics

return to home pagenavigate

Last Updated: July 11, 2006


Contact Us | Products | Our Company
Site Map | Policies
© Copyright 2006 Axiomatic Technologies Corporation